View MIC3839BMM_6889504.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

august 2003 1 mic3838/3839 mic3838/3839 micrel mic3838/3839 flexible push-pull pwm controller general description the mic3838 and mic3839 are a family of complementary output push-pull pwm control ics that feature high speed and low power consumption. the mic3838/9 are ideal for telecom level (36v to 75v) isolated step down dc/dc conversion applications where high output current, small size, and high efficiency are required the mic3838/9 are designed for high flexibility with minimum pin-count. the devices are easily configurable for either voltage-mode or current-mode control. additionally, the mic3838/9 can easily implement a volt-second clamp that automatically limits the duty cycle during input transients, allowing designers to use the smallest possible transformers and power components. a 3v reference output is also avail- able that eliminates the need for an external reference. the dual-ended push-pull architecture of the mic3838/9 allows more efficient utilization of the transformer than single- ended topologies, allowing smaller size dc/dc solutions. additionally, the out-of-phase push-pull topology allows a higher effective duty cycle, reducing input and output ripple as well as stress on the external components. the dead-time between the two outputs is adjustable between 60ns to 200ns, limiting the duty cycle of each output stage to less than 50%. the mic3838 has a turn-on threshold of 12.5v whereas the mic3839 has a lower turn-on threshold of 4.3v. both devices are available in a small size msop-10 package with an operating range of ?0 c to +85 c. data sheets and support documentation can be found on micrel? web site at www.micrel.com. features dual output drive stages in push-pull configuration configurable for current-mode or voltage-mode control easily implements volt-second clamp leading edge current-sense blanking 3v reference output available 130 a typical start-up current 1ma typical run current operation to 1mhz on-chip error amplifier with 4mhz gain bandwidth product internal soft start on-chip v dd clamping output drive stages capable of 500ma peak source current, 1a peak sink current applications high efficiency ?rick?power supply modules half bridge converters full bridge converters push-pull converters voltage-fed push-pull converters telecom equipment and power supplies industrial power supplies 42v automotive power supplies base stations networking power supplies micrel, inc. ?1849 fortune drive ?san jose, ca 95131 ?usa ?tel + 1 (408) 944-0800 ?fax + 1 (408) 944-0970 ?http://www.mic rel.com typical application mic3838x-x v out 12v 100w vref rc vdd outa comp gnd outb ramp fb ilim start-up circuitry driver reference & isolation feed forward ramp/ volt sec clamp v in 36v to 75v voltage-mode half-bridge converter circuit
mic3838/3839 micrel mic3838/3839 2 august 2003 ordering information turn on turn off part number threshold threshold temperature range package mic3838bmm 12.5v 8.3v ?0 c to +85 c msop-10 MIC3839BMM 4.3v 4.1v ?0 c to +85 c msop-10 pin configuration 1 comp fb ilim ramp 10 vref vdd outa outb 9 8 7 2 3 4 rc gnd 6 5 msop-10 (mm) pin description pin number pin name pin function 1 comp comp is the output of the error amplifier and the input of the pwm comparator. the error amplifier in the mic3838 is a true low-output imped- ance, 4mhz operational amplifier. as such, the comp pin can both source and sink current. however, the error amplifier is internally current limited, so that zero duty cycle can be externally forced by pulling comp to gnd. the mic3838 family features built-in full cycle soft start. soft start is imple- mented as a clamp on the maximum comp voltage. 2 fb the inverting input to the error amplifier. 3 ilim the input to the peak current, and overcurrent comparators. the overcurrent comparator is only intended for fault sensing. exceeding the overcurrent threshold will cause a soft start cycle. an internal mosfet discharges the current sense filter capacitor to improve dynamic perfor- mance of the power converter. 4 ramp input to the pwm comparator. sawtooth ramp for pwm control. allows for either current-mode or voltage-mode control. an internal mosfet dis- charges the current sense filter capacitor. 5 rc the oscillator programming pin. only two components are required to program the oscillator, a resistor (tied between v dd and rc), and a capaci- tor (tied between rc and gnd). the approximate oscillator frequency is determined by the simple formula: f 1.41 rc oscillator = the recommended range of timing resistors is between 7k ? and 200k ? and range of timing capacitors is between 100pf and 1000pf. timing resistors less than 7k ? should be avoided. for best performance, keep the leads between components as short as possible. separate ground and vdd traces to the external timing network are encouraged. 6 gnd ground. return path for signal and gate drive functions.
august 2003 3 mic3838/3839 mic3838/3839 micrel pin description pin number pin name pin function 7, 8 outb, outa alternating high current output stages. both stages are capable of driving the gate of a power mosfet. each stage is capable of 500ma peak source current, and 1a peak sink current. the output stages switch at half the oscillator frequency, in a push/pull configuration. when the voltage on the rc pin is rising, one of the two outputs is high, but during fall time, both outputs are off. this ?ead time between the two outputs, along with a slower output rise time than fall time, insures that the two outputs can not be on at the same time. this dead time is typically 60ns to 200ns and depends upon the values of the timing capacitor and resistor. the high-current output drivers consist of mosfet output devices, which switch from v dd to gnd. each output stage also provides a very low impedance to overshoot and undershoot. this means that in many cases, external schottky clamp diodes are not required. 9 vdd the power input connection for this device. total v dd current is the sum of quiescent v dd current and the average gate drive (out) current. knowing the operating frequency and the mosfet gate charge (qg), average out current can be calculated from iout = qg ?f, where qg is the total gate change of all mosfets (outa and outb) and f is oscillator switching frequency. to prevent noise problems, bypass vdd to gnd with a ceramic capacitor as close to the chip as possible. a 1 f decoupling capacitor is recommended. 10 vref internal 3v supply. will source 1ma maximum.
mic3838/3839 micrel mic3838/3839 4 august 2003 electrical characteristics (note 5) t a = t j = ?0 c to +85 c, v dd =10v, note 10 ,1 f capacitor from v dd to gnd, r=22k ? , c=330pf. parameter condition min typ max units internal reference section output voltage i out = 0ma 2.85 3.0 3.15 v line regulation mic3838 9v v dd 12v 2 10 mv mic3839 5v v dd 12v load regulation i out = 1ma 14 30 mv oscillator section oscillator frequency 180 200 220 khz oscillator amplitude/v dd note 6 0.44 0.5 0.56 v/v dd error amp section input voltage comp = 2v 1.95 2 2.05 v input bias current ? 1 a open loop voltage gain (guaranteed by design) 60 80 db comp sink current fb = 2.2v, comp = 1v 0.3 2.5 ma comp source current fb = 1.3v, comp = 3v, note 7 ?.15 ?.5 ma comp pm clamp voltage v fb = 0v 3.1 3.6 4.0 v pwm section maximum duty cycle measured at outa or outb 48 49 50 % minimum duty cycle comp = 0v 0% current sense section gain guaranteed by design, note 8 1.9 2.2 2.5 v/v i lim maximum input signal note 9 0.45 0.5 0.55 v i lim to output delay comp = 3v, i lim from 0mv to 600mv 70 200 ns ramp or i lim source current ?00 na ramp or i lim sink current ramp = i lim = 0.5v, rc = 5.5v note 10 510 ma i lim over current threshold 0.7 0.75 0.8 v comp to ramp offset ramp = i lim = 0v 0.35 0.8 1.2 v output section out low level i = 100ma 0.5 1 v out high level i = ?0ma, v dd ?out 0.5 1 v rise time c l = 1nf 25 60 ns fall time c l = 1nf 25 60 ns absolute maximum rating (note 1) supply voltage (i dd 10ma) ...................................... +15v supply current ........................................................... 20ma outa/outb source current (peak) ...................... ?.5a outa/outb sink current (peak) ............................ 1.0a comp pin .................................................................... v dd analog inputs (fb, ilim, ramp) ......... ?.3v to v dd +0.3v not to exceed 6v junction temperature .............................. ?5 c to +150 c storage temperature (t s ) ....................... ?5 c to +150 c lead temperature (soldering, 10 sec.) ................... +300 c esd rating, note 3 ...................................................... 2kv operating ratings (note 2) v dd input voltage (v dd ) .......................................... note 4 oscillator frequency (f osc ) ....................... 10khz to 1mhz ambient temperature (t a ) ......................... ?0 c to +85 c package thermal resistance msop-10 ( ja ) .................................................. 115 c/w
august 2003 5 mic3838/3839 mic3838/3839 micrel parameter condition min typ max units undervoltage lockout section start threshold mic3838, note 11 11.5 12.5 13.5 v mic3839 4.1 4.3 4.5 v minimum operating voltage mic3838 7.6 8.3 9 v after start mic3839 3.9 4.1 4.3 v hysteresis mic3838 3.5 4.2 5.1 v mic3839 0.1 0.2 0.3 v soft start section comp rise time fb = 1.8v, rise from 0.5v to 3v 2.5 20 ms overall section startup current v dd < start threshold (mic3839) 130 260 a operating supply current fb = 0v, ramp = i lim = 0v, notes 11, 12 1.5 2 ma v dd zener shunt voltage i dd = 10ma, note 13 13 14 15 v note 1. exceeding the absolute maximum rating may damage the device. note 2. the device is not guaranteed to function outside its operating rating. note 3. devices are esd sensitive. handling precautions recommended. human body model, 1.5k in series with 100pf. note 4. maximum operating voltage is equal to the v dd (zener) shunt voltage. when operating at or near the shunt voltage, care must be taken to limit the v dd pin current less than the 20ma v dd maximum current rating. note 5. specification for packaged product only. note 6. measured at rc. note 7. comp pin is internally clamped to 3.65v(typ.). comp pin source current is measured at v comp = 3.0v to avoid interferring with clamp. minimum source current is higher as v comp approaches v clamp . note 8. gain is defined by a = ? ? v v comp cs , 0 v cs 0.4v. note 9. parameter measured at trip point of latch with fb at 0v note 10. the internal current sink on the ramp and i lim pin are designed to discharge an external filter capacitor. it is not intended to be a dc sink path. internal discharge fet should be able to discharge the volt-sec clamp and feed-forward circuits in the figure below withi n 50ns. note 11. for mic3838, set v dd above the start threshold before setting at 10v. note 12. does not include current in the external oscillator network. note 13. start threshold and zener shunt threshold track one another.
mic3838/3839 micrel mic3838/3839 6 august 2003 typical characteristics 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 02468101214 i dd current (ma) v dd (v) mic3838 i dd current 0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 02468101214 i dd current (ma) v dd (v) mic3839 i dd current 1.220 1.230 1.240 1.250 1.260 -40 -20 0 20 40 60 80 100 120 140 i dd current (ma) temperature ( c) mic3838 i dd current vs. temperature v in = 10v 1.000 1.100 1.200 1.300 1.400 -40 -20 0 20 40 60 80 100 120 140 i dd current (ma) temperature ( c) mic3839 i dd current vs. temperature v in = 10v v in = 5v frequency (khz) resistance (k ? ) oscillator frequency vs. rc values c = 330pf c = 100pf c = 220pf c = 1000pf c = 680pf c = 470pf v dd = 10v c = 270pf 10k 100k 1m 50k 100k 150k 200k 0 50 75 100 125 150 175 200 0 100 200 300 400 500 600 700 800 900 1000 deadtime (ns) capacitance (pf) rc pin capacitance vs. deadtime 83 84 85 86 87 88 89 0 20 40 60 80 100 120 140 160 180 200 deadtime (ns) resistance (k ? ) rc pin resistance vs. deadtime -1.00 -0.50 0.00 0.50 1.00 1.50 -40 -20 0 20 40 60 80 100 120 140 frequency variation (%) temperature ( c) mic3838 oscillator variation vs. temperature v in = 10v -1.500 -1.000 -0.500 0.000 0.500 1.000 1.500 2.000 -40 -20 0 20 40 60 80 100 120 140 frequency variation (%) temperature ( c) mic3839 % oscillator variation vs. temperature v in = 10v v in = 5v -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 02468101214 oscillator (%) v dd (v) mic3839 oscillator variation vs. v dd operating 1.92 1.94 1.96 1.98 2.00 2.02 2.04 4 6 8 1012141618 v ref (v) v dd (v) mic3839 error amplifier reference vs. v dd 1.990 2.000 2.010 2.020 2.030 2.040 -40 -20 0 20 40 60 80 100 120 140 v ref (v) temperature ( c) mic3838 error amplifier reference vs. temperature v in = 10v
august 2003 7 mic3838/3839 mic3838/3839 micrel 2.000 2.010 2.020 2.030 2.040 -40 -20 0 20 40 60 80 100 120 140 v ref (v) temperature ( c) mic3839 error amplifier reference vs. temperature v in = 10v v in = 5v 0.5 0.51 0.52 0.53 0.54 0.55 0.56 8 9 10 11 12 13 14 15 16 v threshold (v) v dd (v) mic3838 current limit threshold vs. v dd 0.520 0.525 0.530 0.535 0.540 02468101214 v threshold (v) v dd (v) mic3839 peak current limit vs. v dd 0.515 0.520 0.525 0.530 0.535 0.540 0.545 -40 -20 0 20 40 60 80 100120140 v threshold (v) temperature ( c) mic3838 peak current limit vs. temperature v in = 10v 0.500 0.505 0.510 0.515 0.520 0.525 0.530 0.535 0.540 0.545 0.550 -40 -20 0 20 40 60 80 100120140 v threshold (v) temperature ( c) mic3839 peak current limit vs. temperature v in = 5v v in = 10v 2.960 2.970 2.980 2.990 3.000 3.010 3.020 4567891011121314 v ref (v) v dd (v) mic3839 3v reference voltage vs. v dd 2.950 2.960 2.970 2.980 2.990 3.000 3.010 3.020 -40 -20 0 20 40 60 80 100120140 v ref (v) temperature ( c) mic3838 3v reference vs. temperature v in = 10v 2.950 2.960 2.970 2.980 2.990 3.000 3.010 3.020 3.030 3.040 3.050 3.060 -40 -20 0 20 40 60 80 100120140 v ref (v) temperature ( c) mic3839 3v reference vs. temperature v in = 10v v in = 5v -40 -20 0 20 40 60 80 100 120 0 45 90 135 180 1e+0 1e+1 1e+2 1e+3 1e+4 1e+5 1e+6 1e+7 gain (db) phase ( ) frequency (hz) mic3838 error amplifier phase-gain vs. frequency 2.96 2.97 2.98 2.99 3.00 3.01 3.02 0 0.5 1.0 1.5 v ref (v) reference current (ma) mic3839 3v reference voltage vs. current v dd = 4.3v v dd = 10.0v
mic3838/3839 micrel mic3838/3839 8 august 2003 functional description the mic3838/9 is a high-speed power supply controller with push-pull output drive capability. mic3838 has a higher v dd turn-on threshold and more hysteresis between v dd turn-on and turn-off than the mic3839. the outputs of the controller operate in a push-pull fashion with a guaranteed dead time between them. a block diagram of the mic3838/9 controller is shown in figure 1. functional diagram t q /q q s r q s r q s r oscillator v dd ok v dd v dd e1v peak current comparator overcurrent comparator pwm comparator pwm latch slope = 1v/ms soft start 2.2v 2.0v 0.5v r 0.8v 14v v dd outa outb gnd 0.5v 1.2r 0.75v error amplifier rc v ref fb comp ramp ilim voltage reference 3.65v figure 1. mic3838 block diagram mic3838 330pf 330pf v in = 36v to 75v 50k 150k 13k 4.5k v comp 0.5v 0.75v peak current comparator over current comparator pwm comparator oscillator v max at ramp input = 1.5v v max at i lim input = 0.5v figure 2. volt second clamp and voltage feed forward circuit v dd and turn-on sequence the oscillator and output gate drive signals are disabled when v dd is lower than the turn on threshold. circuitry in the output drivers eliminates glitching or random pulsing during the start-up sequence. the oscillator is enabled when v dd is applied and reaches the turn-on threshold. the v dd com- parator also turns off the internal soft-start discharge fet, slowly bringing up the comp pin voltage. the v dd pin is internally clamped. as v dd approaches this clamp voltage, the v dd current will increase over the normal current draw of the ic. idd currents greater than 20ma may cause excessive power dissipation in the mic3838/9.
august 2003 9 mic3838/3839 mic3838/3839 micrel soft start the soft start feature helps reduce surge currents at the power supply input source. an internal current source and capacitor ramp up from 0v to near v dd at a typical rate of 1v/ms. the soft start feature limits the output voltage of the error amplifier at the comp pin. as the soft start voltage rises, it allows the comp pin voltage to rise, which in turn allows the duty cycle of the output drivers to increase. the internal soft start voltage is discharged and remains discharged during the following conditions: 1. the v dd voltage drops below the turn-off threshold. 2. the voltage on the cs pin exceeds the overcur- rent comparator threshold. once the internal soft start discharge fet is turned on, it cannot be turned off until the internal soft start voltage drops down below 0.5v. this insures a clean restart. oscillator the oscillator operates at twice the switching frequency of either outa or outb. the oscillator generates a sawtooth waveform on the rc pin. the rising edge of the waveform is controlled by the external resistor/capacitor combination. the fall time is set by the on-resistance of the discharge fet (see figure 3). the fall time sets the delay (dead time) between the turn-off of one output driver and the turn-on of the other driver. a toggle flip-flop insures that drive signals to outa and outb are alternated and therefore insures a maximum duty cycle of less than 50% for each output driver. graphs of component values vs. oscillator frequency and dead time are shown in the typical characteristic section of this specification. q s r 0.2v vdd 2 v dd oscillator output rc 4 figure 3. oscillator the voltage source to the resistor/capacitor timing compo- nents is v dd . the internal turn-off comparator threshold in the oscillator circuit is v dd /2. this allows the oscillator to track changes in v dd and minimize frequency variations in the oscillator. the oscillator frequency can be roughly approxi- mated using the following formula: f 1.41 rc oscillator = where: frequency is in hz resistance is in ohms capacitance is in farads. graphs of oscillator frequency and dead time vs component values are shown in the typical characteristic section of this specification. the recommended range of timing resistors and capacitors is 7k ? to 200k ? and 100pf to 1000pf. to minimize oscillator noise and insure a stable waveform the following layout rules should be followed: 1. the higher impedance of capacitor values less than 100pf may causes the oscillator circuit to become more susceptible to noise. parasitic pin and etch trace capacitances become a larger part of the total rc capacitance and may influence the desired switching frequency. 2. the circuit board etch between the timing resistor, capacitor, rc pin and ground must be kept as short as possible to minimize noise pickup and insure a stable oscillator waveform. 3. the ground lead of the capacitor must be routed close to the ground lead of the mic3838/9. current sensing and overcurrent protection the features are: peak current limit overcurrent limit internal current sense discharge front edge blanking in current mode control, a pwm comparator uses the inductor current signal and the error amplifier signal to determine the operating duty cycle. in the mic3838/9 the signal at the cs pin is level shifted up before it reaches the pwm comparator as shown in figure 1. this allows operation of the error amplifier and pwm comparator in a linear region. there are two current limit thresholds in the mic3838/9; peak current limit and overcurrent limit. the normal operating voltage at the i lim pin is designed less than these thresholds. a pulse-by-pulse current limit occurs when the inductor current signal at the i lim pin exceeds the peak current limit threshold. the on-time is terminated for the remainder of the switching cycle, regardless of whether outa or outb is active. if the signal at the i lim pin goes past the peak threshold and exceeds the overcurrent limit threshold, the overcurrent limit comparator forces the soft start node to discharge and initiates a soft start reset. an internal fet discharges the ramp and i lim pins at the end of the oscillator charge time. the fet turns on when the voltage on the rc pin reaches the upper threshold (v dd /2) and remains on for the duration of the rc pin discharge time and for typically 100ns after the start of the next on-time period. the 100ns period at the beginning of the on-time implements a front edge blanking feature that prevents false triggering of the pwm comparator due to noise spikes on the leading edge of the current turn-on signal. the front edge blanking also sets the minimum on-time for outa and outb. the timing diagram for the ramp pin is shown in figure 4.
mic3838/3839 micrel mic3838/3839 10 august 2003 rc pin max on time dead time oscillator reset ramp pin outa outb dead time front edge blanking minimum on time figure 4. timing diagram error amplifier the error amplifier is part of the voltage control loop of the power supply. the fb pin is the inverting input to the error amplifier. the non-inverting input is internally connected to a reference voltage. the output of the error amplifier, comp, is connected to the pwm comparator. a voltage divider between the error amplifier output (comp pin) and the pwm comparator allows the error amplifier to operate in a linear region for better transient response. the output of the error amplifier (comp pin) is clamped at typically 3.65v to prevent the comp pin from rising up too high during startup or during a transient condition. this feature improves the transient response of the power supply. output drivers outa and outb are alternating output stages, which switch at half the oscillator frequency. a toggle flip-flop in the mic3838/9 guarantee both outputs will not be on at the same time. the rc discharge time is the dead time, where both outputs are off. this provides an adjustable non-overlap time to prevent shoot through currents and transformer saturation in the power supply. the output drivers are inhibited when v dd is below the undervoltage threshold. internal circuitry prevents the output drivers from glitching high when v dd is first applied to the mic3838/9 controller. decoupling and pcb layout pcb layout is critical to achieve reliable, stable and efficient operation. a ground plane is required to control emi and minimize the inductance in power, signal and return paths. the following guidelines should be followed to insure proper operation of the circuit: low level signal and power grounds should be kept separate and connected at only one location, preferably the ground pin of the control ic. the ground signals for the current sense, voltage feedback and oscillator should be grouped together. the return signals for the gate drives should be grouped together and a common connection made at the ground pin of the controller. the low level signals and their returns must be kept separate from the high current and high voltage power section of the power supply. avoid running sensitive traces, such as the current sense and voltage feedback signals next to or under power components, such as the switching fets and transformer. if a current sense resistor is used, it s ground end must be located very close to the ground pin of the mic3838/9 controller. careful pcb layout is necessary to keep the high current levels in the current sense resistor from running over the low level signals in the controller. a minimum 1 f bypass capacitor must be connected directly between the v dd and gnd pins of the mic3838/9. an additional 0.1 f capacitor between the v dd end of the oscillator frequency setting resistor and the ground end of the oscillator capacitor may be necessary if the resistor is a distance away from the main 1 f bypass capacitor
august 2003 11 mic3838/3839 mic3838/3839 micrel package information 0.15 (0.006) 0.05 (0.002) 0.50 bsc (0.020) 6 max 0 min 3.15 (0.122) 2.85 (0.114) 3.10 (0.122) 2.90 (0.114) 0.30 (0.012) 0.15 (0.006) 0.26 (0.010) 0.10 (0.004) 1.10 (0.043) 0.94 (0.037) dimensions: mm (inch) 0.70 (0.028) 0.40 (0.016) 4.90 bsc (0.193) 10-pin msop (mm) micrel, inc. 1849 fortune drive san jose, ca 95131 usa tel + 1 (408) 944-0800 fax + 1 (408) 944-0970 web http://www.micrel.com the information furnished by micrel in this datasheet is believed to be accurate and reliable. however, no responsibility is as sumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intend ed for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant inj ury to the user. a purchaser s use or sale of micrel products for use in life support appliances, devices or systems is at purchaser s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2003 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC3839BMM

	To Download MIC3839BMM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .